Design Features According to UL & FM All interior bolt or screw that are exposed to pumped liquid shall be of rolled bronze or corrosion resistant material The pump shall be provided with automatic air-release valve, circulation relief valve and pressure gauges Bearings shall have an L-10 rating of

Design Features According to UL & FM All interior bolt or screw that are exposed to pumped liquid shall be of rolled bronze or corrosion resistant material The pump shall be provided with automatic air-release valve, circulation relief valve and pressure gauges Bearings shall have an L-10 rating of

Capacity: 50 GPM to 1000 GPM Working Pressures: 60 to 234 PSI Speed: 2900,3000, AND 3500 RPM Compliance to NFPA 20 Design Requirements Wide Range of Flows and Pressures Available in Electric Motor and Diesel Engine driven configuration Hydrostatic and Certified Performance Tests Suitable for Commerc

EBITT - UL+FM A ready-to-site pump system designed according to international fire standards. • UL Listed and FM Approved system components • NFPA 20 compliant design • Electric + Electric + Jockey configuration • Electric + Diesel + Jockey configuration • High flow capacity up to 3000 GPM • Pressur

Capacity: 200 GPM – 2000 GPM Pressures: 40 – 355 psi Maximum Working Pressures: 290 to 395 PSI Speed: 1480,1760, 2900,2980, 3000 RPM Dynamically Balanced Impeller extends bearing life and ensures smoother operation. Designed and built as per UL 448 AND NFPA20 for maximum reliability. Constructed in

The pump specifications range from 30–3000 m3/h at a pressure on up to 150 mWC and are designed according to the needs of the vessel in question and is customized to meet the needs of required specifications.

The enclosure is H-60 insulated in material AISI 316 stainless steel. All our containerised equipment is designed for easy installation and good access to all major components. The units may be equipped with fire and gas detection and fire extinguishing system. Fire rated container (A-60, H-60, H-1

The diesel/hydraulic is suitable when the main fire pump installation must be done above the draught line, typically in a compartment below deck in the fore peak. A hydraulic driven lift pump will be installed taking suction from a sea chest, pumping the water to the booster pump connected directly

Fire Pump Group Control System Individual control panels are used for electric pump, diesel pump and jockey pump Lock mechanism are used on panels Continuous grounding Pumps can run by manual control and emergency-run mechanical control on controller By the help of Locked Rotor Protection (LRP), i

Floway® fire pumps are recognized worldwide for superior quality, top hydraulic performance and long service-life Our expertise in fire pumps stems over 50 years, during which time we have solely concentrated on vertical pump innovation.

Large hotels, hospitals , schools，office buildings，supermarkets, commercial residential buildings, metro stations, railway stations, airports, kinds of transportation tunnels, petrochemical plants, thermal power plants, terminals, oil depots, large warehouses and industrial and mining enterprises, e

Dinflow End Suction Bare Shaft Pumps, Dinbloc close coupled Pump and the Linebloc in line suction pump are made to DIN Standard EN733 ( formerly 24255).

High efficiency horizontal single stage end suction pumps complying with DIN EN 733.

Reduces a higher inlet pressure to lower outlet pressure. Provides a consistent outlet pressure over a wide flow range. Pilot operated main valve is not subject to pressure fall-off. Outlet pressure is adjustable with a single screw. Can be maintained without removal from the pipeline. Flanged Ends

UL / FM at 300 psi. Single piece through shaft. The Weflo UL / FM Butterfly Valve – Wafer Style has a Vulcanized Disc design that provides bubble tight shut-off every time. Low torque operation – high cycle life. Gear Operated. Includes built-in Supervisory (Tamper) Switch. Fusion Bonded Epoxy Coate

UL / FM at 300 psi. Vulcanized Disc design provides bubble tight shut-off every time. Low torque operation – high cycle life. Gear Operated. Includes built-in Supervisory (Tamper) Switch. UL / FM Butterfly Valve – Grooved Ends to AWWA C606 Standard. Fusion Bonded Epoxy Coated Interior and Exterior t

UL / FM / AWWA Large Diameter Resilient Seated Gate Valves – Mechanical Joint x Mechanical Joint Ends. 14”-16”-18” Sizes are UL / FM at 250 psi rating. 20” and 24” are UL / FM at 200 psi rating. Manufactured to AWWA C515-15 Standard. Mechanical Joint Ends are to AWWA C111 / AWWA C153 Standard. Stain

UL / FM / AWWA Resilient Seated Gate Valves are manufactured in accordance with AWWA C515-15 Standard. They are NSF-61 Certified for Use in Drinking Water Systems and NSF-372 Certified as Lead-Free. Body, bonnet, and wedge are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is en

The BEECO® GV-FXG-UL/FM Series is a UL Listed / FM Approved Flanged by Grooved OS&Y (Outside Screw and Yoke) Resilient Seated Gate Valve. It is manufactured in compliance with AWWA C515 Standard. Flanges are to ANSI B16.1, Class 125 drilling pattern. Grooved dimensions are to AWWA C606 Standard. The

The BEECO® GV-FXF-UL/FM Series is a UL Listed / FM Approved OS&Y (Outside Screw and Yoke) Resilient Seated Gate Valve. It is manufactured in compliance with AWWA C515 Standard. Flanges are to ANSI B16.1, Class 125 drilling pattern. The body, bonnet, and wedge (disc) are of high strength ductile-iron

UL / FM (including UL-Canada) at 300 psi. The UL / FM Post Indicator Gate Valve – MJ x MJ meets AWWA C515-15 Standard. Mechanical Joint Ends are to AWWA C111 / AWWA C153 Standard. Fusion Bonded Epoxy Coated Interior and Exterior to AWWA C550 Standard. NSF-61 and NSF-372 Certified. Meets the requirem

UL / FM (including UL-Canada) at 300 psi. The UL / FM Post Indicator Gate Valve – Flange x Flange meets AWWA C515-15 Standard. Flanges are to ASME B16.1, Class 125, or ASME B16.42, Class 150 Standard. Fusion Bonded Epoxy Coated Interior and Exterior to AWWA C550 Standard. NSF-61 and NSF-372 Certifie

Weflo manufactures UL / FM Large Diameter Post Indicator Valves in 14” through 24” Sizes. 14”-16”-18” are UL / FM at 250 psi rating. 20” and 24” are UL / FM at 200 psi rating. Manufactured to AWWA C515-15 Standard. Stainless Steel Stem is standard. Fusion Bonded Epoxy Coated Interior and Exterior to