Fukuzawa Valve Co., Ltd.

HTD FEATURE Pressure Ranges 40 psig to 100 psig 3 bar to 8 bar Temperature Ranges – Std.(NBR O-rings) : 20°C~80°C (-4°F~176°F) – Lower Temp. (Silicone O-rings) : 40°C~80°C (40°F~176°F) – High Temp. (Viton O-rings) : 15°C~150°C (+5°F~300°F) – Note : Special grease is required for low and high temperature service condition. Operating Media Filtered dry or lubricated air for non-corrosive gas, water or light hydraulic oil. The maximum particle size must not exceed 30 microns. Stroke Adjustment 0° and 90° with standard adjustment ±5°. Lubrication All moving parts are factory lubricated for entire life cycle of actuator. Construction Twin piston rack and pinion actuator design, suitable for indoor and outdoor installation. Connections Bottom drilling complies with ISO 5211/DIN 3337 to match valve. Interface for solenoid valve, shaft top end and top drilling for assembling accessories are in accordance with VDINDE-3845, NAMUR standard. Inspection Every actuator is hydraulically tested, certified and guaranteed for a minimum of 500,000 cycles.

Pressure Ranges 40 psig to 100 psig 3 bar to 8 bar Temperature Ranges – Std.(NBR O-rings) : 20°C~80°C (-4°F~176°F) – Lower Temp. (Silicone O-rings) : 40°C~80°C (40°F~176°F) – High Temp. (Viton O-rings) : 15°C~150°C (+5°F~300°F) – Note : Special grease is required for low and high temperature service condition. Operating Media Filtered dry or lubricated air for non-corrosive gas, water or light hydraulic oil. The maximum particle size must not exceed 30 microns. Stroke Adjustment 0° and 90° with standard adjustment ±5°. Lubrication All moving parts are factory lubricated for entire life cycle of actuator. Construction Twin piston rack and pinion actuator design, suitable for indoor and outdoor installation. Connections Bottom drilling complies with ISO 5211/DIN 3337 to match valve. Interface for solenoid valve, shaft top end and top drilling for assembling accessories are in accordance with VDINDE-3845, NAMUR standard. Inspection Every actuator is hydraulically tested, certified and guaranteed for a minimum of 500,000 cycles.

FEATURE SIZE : 1/2″~48″ (DN15~DN1200) DIM. SPEC : ASME B16.9 / B16.28 JIS B2311 SGP / LG DIN 2605 /2615 /2616 /2617 MATERIAL SPEC : – Carbon & Alloy Steel ASTM A234 / A234M – WPB / WPC / WP11 ASTM A420 / A420M – WPL6 / WPL9 JIS SGP / PY400 DIN ST37.0 / ST35.8 – Stainless Steel ASTM A403 – WP 304 / 304L / 316 / 316L

FEATURE SIZE : 1/8″~4″ (6mm~100mm) W.P. : 200030006000 LBS Material : ASME A105, A182F304 / F304L / F316 / F304H / F316H / F317L / F321 / F11 / F22 / F91 Investment Casting End Type : Threaded DIM.SPEC : MSS – SP79 \ 83 \ 95 \ 97

Material : 304 / 316 / 304L / 316L Casting Process : Investment Casting End Type : Thread Thread : NPT / BSPT / BSP / DIN 2999 / ISO 7-1 / ISO 228

U01 UNION F/F FEATURE Material : 304 / 316 / 304L / 316L Casting Process : Investment Casting End Type : Thread Thread : NPT / BSPT / BSP / DIN 2999 / ISO 7 – 1 / ISO 228

M01 ELBOW 90° FEATURE Material : 304 / 316 / 304L / 316L Casting Process : Investment Casting End Type : Thread Thread : NPT / BSPT / BSP / DIN 2999 / ISO 7 – 1 / ISO 228

FEATURE Material : 304 / 316 / 304L / 316L Casting Process : Investment Casting End Type : Thread Thread : NPT / BSPT / BSP / DIN 2999 / ISO 7 – 1 / ISO 228

FEATURE 1/8″~2″ (DN6~DN50) W.P. : 6000 / 10000 PSI W.T. : -20°C~200°C (-4°F~392°F) Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7-1 & EN 10226

FEATURE Tube end, 1/2″~4″ (DN15~DN100) Body W.P.: 1000 WOG (PN63) Tube End W.P.: 200 WOG W.T.: -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Live-loading design Anti-static device (option) Cavity filled seats Locking device ISO 5211 Mounting pad 2013KB-BPE : Tube end castings have low sulphur content of 0.005-0.017% Extended tube end (ETO)

Pharmaceutical, Food, High Vacuum, BPE Fitting The HAITIMA clean sanitary ball valve is designed to the highest standards to comply with ASME BPE, ASME B16.34 and API598. It is designed with a full “tube bore”, where the ID of the valve equals the ID of the tube and thus ensuring maximum flow capcity with minimum pressure drop across the valve, The full “tube ID” also ensures clean ability and drainability as mandated by ASME BPE. Extended weld ends as per ASME BPE with sulphur Control (0.005 0.017%) for orbital welding.

2049 FEATURE 1/4″~3″ (DN8~DN80) W.P. : 800 WOG (PN50) W.T. : 20°C~200°C (4°F~392°F) Investment casting Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7 – 1 & EN 10226

FEATURE 1/2″~4″ Design : API 602, BS 5352, ASME B16.34 Applicable Rating : Class 150 ~ 1500 Temperature Rating : Up to 500°C Structure Features : Bolt Bonnet End Connection : Flange End : ASME B16.5

FEATURE 1/2″~4″ Design : API 602, BS 5352, ASME B16.34 Applicable Rating : Class 150 ~ 2500 Temperature Rating : Up to 500°C Structure Features : Outside Screw & Yoke Bolt Bonnet Rising Stem / Non-Rising Handwheel End Connection : Flange End : ASME B16.5 Cryogenic Type : 2073C Bellows Seal (option)

2077P FEATURE 1/2″~4″ Design : API 602, BS 5352, ASME B16.34 Applicable Rating : Class 150 ~ 2500 Temperature Rating : Up to 500°C Structure Features : Bolt Bonnet / Welded Bonnet / Pressure-Seal Bonnet End Connection : Threaded End : ASME B1.20.1 Socket Welded End : ASME B16.11 Butt Welded End : ASME B16.25

FEATURE 1/2″~4″ Design : API 602, BS 5352, ASME B16.34 Applicable Rating : Class 150 ~ 2500 Temperature Rating : Up to 500°C Structure Features : Outside Screw & Yoke Bolt Bonnet / Welded Bonnet / Pressure-Seal Bonnet Rising Stem / Non-Rising Handwheel End Connection : Threaded End : ASME B1.20.1 Socket Welded End : ASME B16.11 Butt Welded End : ASME B16.25 Cryogenic Type : 2076C (option) Bellows Seal (option)

FEATURE 1/4″~2″ (DN8~DN50) W.P. : 800 WOG (PN50) W.T. : -20°C~200°C (-4°F~392°F) Investment casting Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7-1 & EN 10226

1/2″~14″ (DN15~DN600) W.P. : PN16 / 40 Class 150 / 300 / 600 JIS 10K / 20K W.T. : -20°C~200°C (-4°F~392°F) Investment casting API 6D / API 600 / API 602 (option)

FEATURE 1/2″~12″ (DN15~DN300) W.P. : PN16 / 40 Class 150 / 300 / 600 JIS 10K / 20K W.T. : -20°C~200°C (-4°F~392°F) Investment casting Rising stem API 6D / API 600 / API 602 (option)

1/2″~3″ (DN15~DN80) W.P. : 200 WOG W.T. : -20°C~200°C (-4°F~392°F) Investment casting Socket weld (option) Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7-1 & EN 10226

FEATURE 1/4″~2-1/2″ (DN8~DN65) W.P. : 200 WOG W.T. : -20°C~200°C (-4°F~392°F) Investment casting Rising stem Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7-1 & EN 10226

FEATURE Standard port, 1/4″~2″ (DN8~DN50) W.P. : 2160 WOG W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Anti-static device (option) Locking device ISO 5211 mounting pad Seal welded ends ASME B16.34 Wall thickness NACE MR0175 API 607 Fire safe approved API 608 Design Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7-1 & EN 10226

FEATURE Full port, 2″~24″ (DN50~DN600) W.P. : PN10 / 16 / 25 / 40 Class 150 / 300 / 600 W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Anti-static device ISO 5211 Direct mounting pad Metal seat : 2063-MS (option) Flange dimension : ASME B16.5 EN 1092-1 Face to face : ASME B16.10 API 6D

L port / T port, 1/2″~8″ (DN15~DN200) W.P. : PN16 / 40 Class 150 / 300 JIS 10K W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem ISO 5211 direct mounting pad

FEATURE L port / T port, 1/4″~2″ (DN8~DN50) W.P. : 1000 WOG (PN63) W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Locking device Anti-static device (option) ISO 5211 Mounting pad Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7 – 1 & EN 10226

FEATURE Full port, 1/2″~4″ (DN15~DN100) Body W.P. : 1000 WOG (PN63) Flange End W.P. : PN40 W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Anti-static device (option) Locking device ISO 5211 Mounting pad 2010M (option) ISO 5211 Direct mounting pad 2010D (option) Flange dimension : DIN 2501 – PN40 Face to face : DIN 3202 Part 1 – F1

FEATURE Full port, 1/2″~12″ (DN15~DN300) W.P. : PN16 / 40 W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Anti-static device (option) ISO 5211 Mounting pad Flange dimension : DIN 2501 Face to face : DIN 3202 Part 1 – F4 / F5

Full port, 1/2″~5″ (DN15~DN125) W.P. : 1/2″~2″ – PN16 / 40 2-1/2″~4″ – PN10 / 16 5″ – PN16 Class 150 W.T. : -20°C~200°C (-4°F~392°F) Wafer type Investment casting Blow-out proof stem Anti-static device (option) ISO 5211 Mounting pad

FEATURE Full port, 1/4″~4″ (DN8~DN100) W.P. : 1000 WOG (PN63) W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Anti-static device (option) Locking device Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7 – 1 & EN 10226

FEATURE Full port, 1/4″~4″ (DN8~DN100) W.P. : 1000 WOG (PN63) W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Anti-static device (option) Locking device Butt weld ends conform to ASME B16.25 & DIN 3239 Part 1

FEATURE Full port, 1/4″~4″ (DN8~DN100) W.P. : 1000 WOG (PN63) W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Anti-static device (option) Locking device Socket weld ends conform to ASME B16.11 & DIN 3239 Part 2

Full port, 1/4″~4″ (DN8~DN100) W.P. : 1/4″~1″ – 2000 WOG (PN150) 1-1/4″~2″ – 1500 WOG (PN100) 2-1/2″~4″ – 1000 WOG (PN63) W.T. : -20°C~200°C (4°F~392°F) Investment casting Blowout proof stem Antistatic device (option) Locking device Tapped & drilled mounting pad (option) TALuft approved (option) Length conform to DIN 3202 Part 4 – M3 : 2006M3 (option) Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7-1 & EN 10226

Reduced port, 1/4″~3″ (DN8~DN80) W.P. : 1000 WOG (PN63) W.T. : -20°C~200°C (-4°F~392°F) Investment casting Blow-out proof stem Anti-static device (option) Locking device Thread type : ASME B1.20.1 (NPT) DIN 2999 & BS 21 ISO 7-1 & EN 1022