MIFAB, Inc.

The BEECO Swing Check valves are used to prevent backflow protecting system equipment. Swing check valves are used to prevent flow reversal in piping systems. They are suitable for service in horizontal or vertical flow upward installation. Swing check valves have low pressure drop and are best suited for moderate velocity applications.

The BEECO Swing Check valves are used to prevent backflow protecting system equipment. Swing check valves are used to prevent flow reversal in piping systems. They are suitable for service in horizontal or vertical flow upward installation. Swing check valves have low pressure drop and are best suited for moderate velocity applications.

The Beeco Full Port Ball Valve is a two piece Bronze Ball Valve with a chrome plated ball. The valve has a blow out proof stem with adjustable packing. Its full port design eliminates the significant pressure losses caused by standard reduced port valves.

The Automatic Control Valve shall be a Ductile Iron Body and Cover design. The Valve shall have a resilient seal disc, guided top and bottom; Bottom guide will be vanes, sliding in a stainless steel seat arrangement, single seated line pressure operated, diaphragm actuated, pilot controlled, valve. The valve shall seal by means of a stainless steel seat. All parts are to be replaceable in the field without removing the valve from the line. All flange dimensions including face to face lengths shall conform to ISO Standards.

The BEECO® GV-FXG-UL/FM Series is a UL Listed / FM Approved Flanged by Grooved OS&Y (Outside Screw and Yoke) Resilient Seated Gate Valve. It is manufactured in compliance with AWWA C515 Standard. Flanges are to ANSI B16.1, Class 125 drilling pattern. Grooved dimensions are to AWWA C606 Standard. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.

The BEECO® GV-FXF-UL/FM Series is a UL Listed / FM Approved OS&Y (Outside Screw and Yoke) Resilient Seated Gate Valve. It is manufactured in compliance with AWWA C515 Standard. Flanges are to ANSI B16.1, Class 125 drilling pattern. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.

The Beeco Eccentric Plug Valve is designed to operate in clean and dirty water applications. The valve performs well in sludge and slurry liquid applications as well. The valve seals with a “drop tight” closure. The interior design allows for a full flow with very little pressure drop.

MIFAB® SUPER-1500-FM hydro mechanical grease interceptor with 1,522 U.S. gallons of liquid holding capacity has a limited lifetime warranty and is made in the U.S.A. out of seamless, rotationally molded High Density Polyethylene with 3/8” uniform wall thickness. Interceptor is designed for above or below ground installation and includes extension pipe gasket for ADS 24N12 (pipe not included) for the adjustable lid system, sample port access, Type 316 stainless steel internal baffle that is secured in place with stainless steel hardware, deep seal trap covered by lid, internal flow control set to 100 GPM, base for support and floor level installation and 4” no hub inlet and outlet connections. Ductile Iron pickable lids, H-20 rated, proof-load tested to 40,000 lbs. provide a water / gas tight seal. The lids are designed in accordance with the loading requirements of AASHTO H-20. The high density polyethylene material is PE 3135 from Dow 9.39 with a density of 0.939 g/cm3. Note that the interceptor is tested and certified to the ASME A112.14.3 Standard, (Type D), CSA B481 and listed with I.A.P.M.O. For indoor/outdoor use.

MIFAB® SUPER-500 gravity grease interceptor with 500 U.S. gallons of liquid holding capacity has a limited lifetime warranty and is made in the U.S.A. out of seamless, rotationally molded High Density Polyethylene with 3/8” uniform wall thickness. Interceptor is designed for above or below ground installation and includes extension pipe gasket for ADS 24N12 (pipe not included) for the adjustable lid system, sample port access, internal baffle, deep seal trap covered by lid, internal air relief by-pass, base for support and floor level installation and 4” no hub inlet and outlet connections. Ductile Iron pickable lids, H-20 rated, proof-load tested to 40,000 lbs. provide a water / gas tight seal. The lids are designed in accordance with the loading requirements of AASHTO H-20. The high density polyethylene material is PE 3135 from Dow 9.39 with a density of 0.939 g/cm3. Note that the interceptor is tested and certified to the ASME A112.14.3, CSA B481 and ANSI Z1001 Standards and listed with I.A.P.M.O. The -PDI model is tested and certified to the PDI G-101 Standard, 100 GPM flow rate.

MIFAB® Lil-35-99 HDPE injection molded hydromechanical grease interceptor with flow rating of 35 GPM and grease holding capacity of 83 lbs. Unit shall include: removable baffle assembly, deep seal trap covered by lid, sewer gas stopper, securing latches, internal stainless steel orifice flow control plate, internal air relief by pass, HDPE injection molded, non skid, rectangular gasketed lid(s). Interceptor shall be tested and certified to the A.S.M.E. A112.14.3 Standard (Type A) and listed with I.A.P.M.O. The Lil-35-99 is also tested and certified as two units in series to the 99% efficiency requirements of the Miami-Dade DERM Standard. (FOG Control, Miami Dade County Code Chapter 24.42.6).

MIFAB® Series Lil-(specify size)-N HDPE injection molded fish scale interceptor with flow rating of ____ (indicate) and liquid holding capacity of ____ (indicate). Unit shall include: two internal straining baffles (3/8″ Dia. holes, 1/2″ apart), internal deep seal trap and HDPE injection molded, non skid, rectangular gasketed lid with securing latches.

MIFAB® Series Lil-(specify size) HDPE injection molded hydromechanical grease interceptor with flow rating of ____ (indicate) and grease holding capacity of ____ (indicate). Unit shall include: removable baffle assembly, deep seal trap covered by lid, sewer gas stopper, securing latches, internal stainless steel orifice flow control plate, internal air relief by pass, HDPE injection molded, non skid, rectangular gasketed lid(s). Interceptor shall be tested and certified to the P.D.I. Standard PDI-G101 (when installed with an external, vented flow control fitting), CSA B481, A.S.M.E. A112.14.3 and listed with I.A.P.M.O. Lil Max grease interceptors are also in compliance with International Plumbing Code (I.P.C.) / I.C.C. by I.A.P.M.O

MIFAB® Series F1100-C-TS(*)-(**) (*specify strainer diameter and (**) finish) MIFAB Top Set finished floor drain with lacquered cast iron body and water proofing membrane clamp, securing and adjustable hardware, allen key vandal resistant stainless steel grate screws and heelproof strainer (specify -1 for nickel bronze and -3 for stainless steel) that can be adjusted vertically and side to side after the pour with 3/4” thick composite strainer protective cover and indicating whisker..

MIFAB® R1200-HC Series lacquered cast iron deep sump roof drain with 15” diameter anchor flange, large cast iron waterproofing membrane clamp ring with integral gravel stop, adjustable extension with auxiliary drainage slots, secondary clamp, and standard self-locking polyethylene dome strainer with a free area of 125 square inches.

MIFAB® R1200-90 Series lacquered cast iron deep sump roof drain with threaded side outlet, 15” diameter anchor flange, large cast iron waterproofing membrane clamp ring with integral gravel stop, and standard self-locking polyethylene dome strainer with a free area of 125 square inches.

MIFAB® R1100 Series lacquered cast iron roof drain with anchor flange, cast iron waterproofing membrane clamp ring with integral gravel stop, and standard self-locking polyethylene dome strainer with a free area of 43 square inches.

MIFAB® R1330 Series lacquered cast iron scupper drain with 45 degree no hub outlet, membrane clamp and 90 degree grate (specify cast iron (Suffix -50) or nickel bronze (Suffix -1)).